Tap drill size for 6-32
#36
0.1065 inches · 2.71 mm · 75% thread engagement
| Tap drill (75% thread) | #36 — 0.1065" / 2.71 mm |
| Major diameter | 0.138" / 3.51 mm |
| Drill for a 100% thread | 0.0974" / 2.47 mm |
| Threads per inch | 32 |
| Pitch | 0.0313" / 0.79 mm |
| Series | UNC (coarse) |
Where the number comes from
A tap cuts the thread; the drill leaves the hole it cuts into. Cutting the full thread form would mean drilling the major diameter less the whole height of the thread:
0.138 − 1.299 ÷ 32 = 0.0974 inches
That is the 100% thread, which nobody drills — the tap has to remove every scrap of metal and usually breaks trying. Charts give 75%, so three quarters of the thread height is cut away and the rest is left as clearance:
0.138 − 0.974 ÷ 32 = 0.1076 inches
The nearest drill that actually exists is #36 at 0.1065 inches, which is 0.0011 inches under the theoretical figure. That is the number printed on every 6-32 tap chart, and this is where it comes from.
The same hole at other engagements
Thread engagement is a choice, not a constant. Less engagement means an easier cut and a longer tap life for very little loss of strength, which is why a machinist working stainless will not drill the chart size.
| Engagement | Theoretical | Drill | Millimetres |
|---|---|---|---|
| 50% | 0.1177" | #32 (0.116") | 2.95 mm |
| 65% | 0.1116" | #34 (0.111") | 2.82 mm |
| 75% — the chart value | 0.1076" | #36 (0.1065") | 2.71 mm |
| 85% | 0.1035" | #37 (0.104") | 2.64 mm |
A 75% thread is close to the practical ceiling: going from 75% to 100% adds only a few per cent of strength and roughly doubles the torque needed to turn the tap. Going the other way, a 65% thread still holds about 95% of the load a 75% thread does, which is why 65% is the usual choice in anything harder than mild steel.
6-32 in metric
6-32 has a major diameter of 3.51 mm and a pitch of 0.79 mm. The nearest metric tap is M4 at 4 mm, which is 0.49 mm larger — far enough apart that there is no confusing the two. An M4 bolt will not enter a 6-32 hole at all, so if a fastener nearly fits, neither of these is the standard you are looking for.
For the drill itself the conversion is straightforward: #36 is 2.71 mm, and a metric drill index will offer 2.7 mm as the nearest size.
What 6-32 is used for
Computer cases, electrical boxes and light sheet metal — one of the most-used small threads in North America.
The same 0.138" screw is also made as 6-40, the fine version, which takes a #33 drill instead. Coarse threads tap faster, tolerate damage better and hold better in soft material.
Frequently asked questions
What size drill bit do I need for a 6-32 tap?
A #36 drill, which is 0.1065 inches or 2.71 mm. That is the standard 75% thread engagement figure, and it is what every published tap chart gives for 6-32.
What size hole do I need for a 6-32 thread?
The same #36 hole — 0.1065 inches. The number comes from subtracting the thread height from the major diameter: 0.138 − 0.974 ÷ 32 = 0.1076 inches, and #36 is the nearest drill that exists.
What is the 6-32 tap drill size in mm?
2.71 mm. There is no metric drill of exactly that size, so a metric drill index gives you 2.7 mm as the nearest — close enough for 6-32 in most materials, though it changes the thread engagement slightly.
Can I use a #34 instead?
Yes, and in hard material you should. #34 gives about 65% thread engagement instead of 75%. That costs very little strength — a 65% thread holds roughly 95% of what a 75% thread does — and it makes the tap markedly easier to turn, which is the trade every machinist makes in stainless or tough alloy.
Other tap sizes
- 6-40 tap drill size — #33
- 8-32 tap drill size — #29
- 8-36 tap drill size — #29
- 10-24 tap drill size — #25
- 10-32 tap drill size — #21
- 12-24 tap drill size — #16
- 12-28 tap drill size — #14
- 1/4-20 tap drill size — #7
- 1/4-28 tap drill size — #3
- 5/16-18 tap drill size — F