108 capacitor value
0.1 pF
0.1 pF · 0.0001 nF · 0 µF
| Marked code | 108 |
| Picofarads | 0.1 pF |
| Nanofarads | 0.0001 nF |
| Microfarads | 0 µF |
| Farads | 1.00e-13 F |
Reading the code
The three digits are not a part number. The first two are the value in picofarads and the third says what to do with them:
10 × 0.01 = 0.1 pF
The last digit here is 8, which is one of the two exceptions. Eight and nine do not mean 10⁸ and 10⁹ — they mean × 0.01 and × 0.1, and they exist so that values below ten picofarads can be written in the same three characters. Read literally, 108 would be 10 × 108 = 1,000 µF, which is not a ceramic capacitor and not what is in your hand.
What 0.1 pF does at frequency
A capacitor's opposition to a signal is its reactance, 1 ÷ (2πfC), and it falls as the frequency rises. Over the range of frequencies a circuit can put across it, a 0.1 pF part covers several orders of magnitude:
| Frequency | Reactance |
|---|---|
| 50 Hz — mains | 31.83 GΩ |
| 1 kHz — audio | 1.59 GΩ |
| 100 kHz — switching | 15.92 MΩ |
| 10 MHz — RF | 159.15 kΩ |
Ten times the frequency is a tenth of the reactance, every time — which is why choosing a decoupling capacitor is really choosing the frequency band you want it to be low-impedance across, and why boards carry several sizes in parallel rather than one large one.
The letter after the number
A code like 108K carries a tolerance letter. It is not part of the value:
| Letter | Tolerance | 0.1 pF means |
|---|---|---|
108J | ±5% | 0.1 pF to 0.11 pF |
108K | ±10% | 0.09 pF to 0.11 pF |
108M | ±20% | 0.08 pF to 0.12 pF |
108Z | +80% / −20% | 0.08 pF to 0.18 pF |
A Z is worth knowing about. +80%/−20% is a real tolerance on cheap high-permittivity ceramics, and it means a part marked 108Z can legitimately be anything from 0.08 pF to 0.18 pF. Those go in decoupling positions where only the rough size matters, never in a timing or filter position.
Where 0.1 pF turns up
undefined
Frequently asked questions
What is the value of a 108 capacitor?
0.1 pF — 0.1 pF · 0.0001 nF · 0 µF. The first two digits are the value in picofarads and the third is how many zeros follow, so 108 is 10 followed by a divide rather than a multiply: 10 × 0.01 = 0.1 pF.
What is a 108 capacitor in µF?
0 µF. Going from picofarads to microfarads is six decimal places, which is where most of the confusion with these codes comes from — 0.1 pF, 0.0001 nF and 0 µF are the same capacitor written three ways.
What does the letter after 108 mean?
Tolerance. 108K is ±10%, 108J is ±5% and 108M is ±20% — so a 108K is anywhere from 0.09 pF to 0.11 pF and still in specification. A Z means +80%/−20%, which is not a mistake: some ceramic dielectrics really are that loose.
What is the impedance of a 108 capacitor at 1 kHz?
1.59 GΩ. Reactance is 1 ÷ (2πfC), so it falls as the frequency rises: the same part is 15.92 MΩ at 100 kHz and 159.15 kΩ at 10 MHz.
Nearby codes
- 128 capacitor — 0.12 pF
- 158 capacitor — 0.15 pF
- 188 capacitor — 0.18 pF
- 228 capacitor — 0.22 pF
- 278 capacitor — 0.27 pF
- 338 capacitor — 0.33 pF
- 398 capacitor — 0.39 pF
- 478 capacitor — 0.47 pF
- 568 capacitor — 0.56 pF
- 688 capacitor — 0.68 pF